Solved A Work Piece Of 300mm Diameter And 600 Mm Length Is Chegg A work piece of 300mm diameter and 600 mm length is to be turned down to 282mm for the entire length. the suggested feed is 1.2mm revolution and the cutting speed is 162m min. the maximum allowable depth of cut is 4.5mm. assuming the tool over travel is 12.0mm and neglecting the approach length calculate the followings. 1) a workpiece of 300 mm diameter and 600 mm length is to be turned down to 282 mm, for the entire length. the suggested feed is 1.2 mm revolution and the cutting speed is 162 m min. the maximum allowable depth of cut is 4.5 mm. assuming the tool over travel is 12.0 mm and neglecting the approach length, calculate the following. i) spindle, rpm ii) feed speed iii) material removal rate iv.
Solved 35 Question 2 A Workpiece Of 600 Mm In Length And Chegg So, the part program is prepared for reducing its diameter by turning for 500 3 = 503 mm length (3 mm is given as allowance for parting off). the tool positions are 1 2 3. Mechanical engineering questions and answers a uniform disc of diameter 300mm and of mass 5kg is mounted on one end of an arm of length 600mm. the other end of arm is free to rotate in a universal bearing . of the rotates about the arm with a speed of about 300 rpm clockwise looking from with what speed will it process about the vertical axis ?. Reservoir a has an elevation of 300 mm circular pipe is connected to it with diameter of 300 mm and length of 200 m, while reservoir b is at an elevation 200 mm with circular pipe connected to it diameter 250 mm and length of 250 m and reservoir c elevation with a circular pipe attached to it, diameter is 600 mm and length of 450mm. Questions and answers from chegg at chegg we understand how frustrating it can be when you’re stuck on homework questions, and we’re here to help. our extensive question and answer board features hundreds of experts waiting to provide answers to your questions, no matter what the subject. you can ask any study question and get expert answers in as little as two hours. and unlike your.
Solved السؤال 4 To Fix A Work Piece With A Length 360mm And Chegg Reservoir a has an elevation of 300 mm circular pipe is connected to it with diameter of 300 mm and length of 200 m, while reservoir b is at an elevation 200 mm with circular pipe connected to it diameter 250 mm and length of 250 m and reservoir c elevation with a circular pipe attached to it, diameter is 600 mm and length of 450mm. Questions and answers from chegg at chegg we understand how frustrating it can be when you’re stuck on homework questions, and we’re here to help. our extensive question and answer board features hundreds of experts waiting to provide answers to your questions, no matter what the subject. you can ask any study question and get expert answers in as little as two hours. and unlike your. Work piece turned will have a taper proportional to the amount of the set over. the method is applicable only to long tapers on long work pieces. but if the work is not too short and if the dead centre is carefully set over very accurate results are obtainable. A reinforced concrete beam has a width of 300 mm and an effective depth of 618 mm. compressive reinforcement (if required) will be placed at d'=60mm. f c=25mpa and f y=415mpa. the beam is to support a factored bending moment of 520 kn m. varphi =0.90. use 2010 2015 nscp. 1. calculate the steel ratio for a balanced section, ρ. 2. determine the governing steel ratio (ρ) following nscp.
Solved Problems 3 A Hollow Workpiece Of 40 Mm Outside Chegg Work piece turned will have a taper proportional to the amount of the set over. the method is applicable only to long tapers on long work pieces. but if the work is not too short and if the dead centre is carefully set over very accurate results are obtainable. A reinforced concrete beam has a width of 300 mm and an effective depth of 618 mm. compressive reinforcement (if required) will be placed at d'=60mm. f c=25mpa and f y=415mpa. the beam is to support a factored bending moment of 520 kn m. varphi =0.90. use 2010 2015 nscp. 1. calculate the steel ratio for a balanced section, ρ. 2. determine the governing steel ratio (ρ) following nscp.
Solved 6 A Hollow Work Piece Of 50 Mm Diameter And 200 Mm Chegg
Solved A Rectangular Workpiece Has The Following Original Chegg